- Vcm 2 ford ids how to#
- Vcm 2 ford ids serial number#
- Vcm 2 ford ids drivers#
- Vcm 2 ford ids update#
- Vcm 2 ford ids full#
To set a new serial number select 'Set New Serial Number' and proceed with serial number setting. Wait about 15 seconds past when the VCM2 beeps and point your browser to Ī. Once the test completes unplug, wait a couple seconds, and then re-plug the VCM2 into the computer.ġ5. Select 'Run System Diagnostics' > 'Next' > 'Test a VCM II Module' > 'Next'ġ4. Select 'Launch Monitor Tool' and confirm on the pop up.ġ3. Plug the VCM2 unit into the computer and wait 90 seconds past beep before proceeding.ġ2. Cleanly unmount the SD card and insert it back into the VCM2.ĩ. On the SD card open 'apps/vci-diags/hwtest-scripts/self-test.sh' for editing.Ĩ. Mount the SD card with a linux machine.Ħ. We are waiting for the SD card to be populated.Ĥ. Wait about 90 seconds after the VCM2 beeps before proceeding. After recovery your VCM2 should be at VCM2 FW version 2.1.1.5.ģ.
Vcm 2 ford ids how to#
Describing how to recover is beyond the scope of this post. You'll need a microSD card for this to work.Ī. I have figured out how to change the serial number of the VCM2 as well as enter test mode, and get a root shell on it. Thread: How to change VCM2 serial number, enter test mode, and get a root shell Programming & Installation of new ECUs (PCM, ABS, Instrument Cluster, Air Bag, Fuel Pumps, etc.)
New Software Re-flash for Existing ECUsħ. Live Data-stream with Recording & Playback Functions for Main ECUsĦ. Read & Clear Diagnostic Trouble Codes (DTCs)ģ. With this Ford VCM II, you can do the following functions: (Most of these function only New Ford VCM II has, while old version Ford VCM does not have most of these functions)Ģ. This provides an advantage for technicians when diagnosing. The CFR is an optional cable that allows the VCM II to monitor and record live data streams. The VCM II has shock resistant rubber ends, making it suitable for garage and workshop environments.ħ. The CFR replaces the Vehicle Data Recorder (VDR).Ħ. It supports the Vehicle Measurement Module (VMM) and new Customer Flight Recorder (CFR).ĥ. The VCM II will be required for all new Ford vehicles and is backwards compatible with most 16 pin Fords. The VCM II is the brand new diagnostics interface from Ford for use with the Integrated Diagnostics Software (IDS).Ĥ.
Vcm 2 ford ids full#
The VCM II provides full dealer diagnostic capabilities for most 16 pin Fords.ģ. It provides dealer-level diagnostics using the IDS software.Ģ. The VCM II is the new Ford OEM diagnostic tool. For module programming, if it gets the error "Selection not available", please contact us, we will send you the ExtendProgramming file to solve.ġ. Please do not use original Ford V93.01 software,the device will not work.Ĥ.
Vcm 2 ford ids update#
Old version firmware cannot use V101/ V108 software, need update the firmware first. Software version is IDS V108, Calibration software: V81 (this calibration software on support PCM programming function for part ford cars, not all, Please pay attention).Ģ. UCDS currently works with the following platforms:įocus II 2004-2011 Focus III 2011, 2015 Kuga I, Kuga II C-MAX S-MAX MONDEO IV Mondeo 2015 Galaxy Tansit Fiesta 2008, 20015 etc.1. You need to select the type of the vehicle or select the service mode for adapter`s firmware update or other service functions. The software interface of the UCDS interface has main window’s mode.
Vcm 2 ford ids drivers#
The UCDS consists of drivers of the serial bus USB-serial (recommended drivers FTDI), hardware adapter and the actual UCDS-programm. – Perform regular language adaptation of the audio modules manufactured by SONY (Russian language only) – Update the calibration (firmware) of the modules and components of the vehicle, including the engine (the so-called chip tuning) – Make the necessary changes to the central configuration of the car, and change the configuration of the modules and components if necessary
– Receive data embedded in the car components and modules, including their part number, version, calibration, serial number – Diagnose the majority of car parts and components that are connected to a central electrical module (GEM, BCMii) through the data bus (CAN) Read & Clear Diagnostic Trouble Codes (DTCs)Ħ. Live Data-stream with Recording & Playback Functions for Main ECUsģ. Programming & Installation of new ECUs (PCM, ABS, Instrument Cluster, Air Bag, Fuel Pumps, etc.)Ģ. OS: Windows 7, Windows 8, Windows 10 32bit and 64bitġ. Needs to be produced after 2000 year, older computer can not run the software.ģ. Ford VCM 2 PRO VCM II V119 + V2.0.7.3 UCDS Pro 2 in 1 Diagnostic Tool for Ford MazdaĢ.VCM 2 Pro includes VCM2 and UCDS all functionsģ.Ford UCDS Pro+ Version:V2.0.7.3 Full License Software With 15 TokensĢ.
0 kommentar(er)
